|
|
||||
Hi,
My combi boiler has turned off for some reason and i do not know how to turn the burner back on so could someone tell me how to,
Please help im freezing!!
cant find any red button or a on switch just a load of lights
tried reseting it but still not working and the only red thing i can find when i turn it water comes out of the overflow.
Related posts:
- How do I lower the pressure on a combi boiler?
My boiler’s not working and we desperately need hot water – the people won’t be free till next Tuesday to fix it! Please help: The pressure on the boiler is too high – I need to lower it. I saw that there were taps at the bottom, and turned one, only to have the pressure increase even further! I need to get the pressure down. Help much appreciated, thanks!... - Combi Boiler Water Pressure Issues?
We recently had a combi boiler installed in our rented property. Initially the plumbers left the cold water feed from the tank in the loft so the combi boiler was only supplying the hot water. Unfortunately due to the differing pressures (i think), the cold water feed was excessive whilst using the shower the overflow pipe from the loft rained from the side of the house. The plumbers have since rectified that problem by removing the cold water tank and using the boiler to supply both the hot and cold. Unforunately the water pressure is now so low that it takes 30 mins to fill the bath. Also the shower now operates too hot and eventually (after a few mins) runs cold then hot again. Any help would be appreciated.... - Gas boiler, hot water heater, turn on and off, which is most efficient?
I live in a studio apartment by myself and only need hot water in the mornings to shower. Do i save a significant amount of gas by just turning it on in the morning, taking a shower, and turning it off? Its a bit of a hassle, but if it saves money and gas i think its worth it. Let me know, thanks for the help. i don’t mean a timer, i mean i got physically and turn on and off the heater, i live in mexico where this is common and didn’t know if it was just a old wives tale or actually true... - Why does my central heating makes a thump when I turn on a hot water tap?
My Vaillant central heating system is fairly new and works ok. No one including the installer knows why it makes a thump if turn on a hot water tap when the heating is on. There is no thump when the heating is off.... - Why does my combi boiler pressure shoot up to 3bar?
I have a Baxi combi boiler (installed just over a year ago) and it has ran fine (opperating around 1.5-2bar) up until the 1 year warranty ran out (sods law!). Now when the system is off the pressure goes right down to 0bar. When I turn the heating on it goes up to 3bar. I have checked for leaks and bends/blocks in the flexi pipes (which there aren’t any) and also bled the system. When I turn the heating on (from 0bar pressure) the boiler makes cluncking sounds. Anyone have any ideas before I fork out a tonne for the plumbers? Thanks...
Posted in Discussion
Assuming the pilot light has just gone out, you just need to re-ignite it. There should be a switch or button (probably piezo electric), just turn or push this button and you should be back in business.
You should check to see that there is power to the boiler in the first place so check your fuses!
If you are still stuck, check the instruction manual for your boiler. If you no longer have it, check on the Internet for the model number.
Hi,mine has a re set button if yours does too ,just press it. then you should get heat very soon.Usually the re set button is orange,so if the orange light is on then that is the problem.
You have what sounds like a fault on your boiler.
Water coming out of the pipe outside when you turn the red knob which is the pressure relief valve, and the pressure in the system has gone down, your boiler will have a pressure switch which will stop the boiler coming on with low pressure to stop any damage to the boiler. Try topping up the system see what happens, should be between 1.5 bar and 2 bar.
It could be a number of things, and without knowing the make and model it would be difficult to make any suggestions.
Best to have a look on Corgi’s website and look for an engineer near you.